Recent Posts

Pages: [1] 2 3 ... 9
1
Site News / Contact Via Phone
« Last post by Alex on April 12, 2017, 02:39:34 PM »
The forum is no longer actively monitored. To contact RC, use the phone number listed on the main page under the "Contact" block on the left. 
2
General Discussion / Re: Looking for Precision Eagle 4.2 prop hub
« Last post by Fighterpilot on January 24, 2017, 08:31:44 PM »
I'm trying to figure out how to get some information on having a longer prop hub made for my 4.2 sachs. Ralph did some work for me years ago and I'd like to see if I can get a custom hub made for my engine. Where do I go for that type of info on this site or do I just call the contact number on the home page. This is the second time I'm trying to post on this forum and I'm not having any success seeing my post after I hit the "Post" response below.
3
General Discussion / Re: Looking for Precision Eagle 4.2 prop hub
« Last post by Fighterpilot on January 24, 2017, 08:26:06 PM »
I am confused. I logged onto this site because it said that I can get RC engine service here. I had Ralph do some work for me in years past; however, I see no place on this site to ask a question about service or machine work on engines. What am I missing here?
4
General Discussion / Buddy list
« Last post by rcplanker on July 12, 2016, 10:33:34 AM »
I am a newby and pocking around and removed Alex my one and only buddy from my list and can I get him back???

Thanks
Geno
5
For Sale / prop hubs
« Last post by dvines on June 29, 2016, 01:40:42 PM »
looking for prop hubs for a long shaft ryobi 31cc engine
6
General Discussion / Zenoah G62 Conversion
« Last post by RyanGilmore on April 24, 2016, 07:45:52 AM »
I am looking to get a Zenoah G62 conversion by Ralph Cunningham. This will be going on a Top Flite G62. Can you please PM me?

Thanks,
Ryan
7
General Discussion / Looking for Precision Eagle 4.2 prop hub
« Last post by camarocab on January 22, 2016, 11:03:05 AM »
HI,

I am looking for a standard prop hub for my Precision Eagle 4.2 engine. I actually have the 4 blades Byron setup.

I don't want to use it this way, that's why I am loolking for a standard 2 blades setup that fit this engine.

I am here because someone on Rcgroups told me to contact Ralph Cunningham. ;)

Thanks for you help.

Tom
8
General Discussion / supertigre 4500 converted to gas
« Last post by scratch builder on December 14, 2015, 10:44:59 PM »
anything special I will need to complete this task? thanks in advance,,,tony
9
How-Tos and Knowledge Base / G38 crank repair
« Last post by howpow on December 12, 2015, 02:05:25 PM »
I have a couple of G38s with cranks that dont run true after a crash.  Is there a way to straighten??   Can I send them to you to fix?? What is the cost?   Also need to replace the lower rod end bearing on one of them.  Please advise  Thanks
10
General Discussion / T&G 3.4 Sachs engine
« Last post by biker02 on April 26, 2015, 01:14:54 PM »
I bought a new T&G 3.4 engine in the early 90's and never ran it. I got out of the sport for over 17 years and now want to use this engine on a new plane but I can't get it to run right. Do you work on these and if not can you recommend someone.

Thanks,

A.J. Centineo
Pages: [1] 2 3 ... 9